Difference between revisions of "Password Recovery Procedure for the Cisco AIR-CAP2602I-E-K9"

From NesevoWiki
Jump to navigationJump to search
(Created page using the commands joerg found and I found on https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/9215-pwrec-2.html#resios)
 
m (Fixed formatation errors, using blockquotes instead of <code>-elements for example console output (forgot code-elements were for single line stuff))
Line 2: Line 2:
 
<br/><br/>
 
<br/><br/>
 
'''Step 2''': A new prompt <code>ap: </code> should appear in the console. Now type in the following commands as shown in the example:
 
'''Step 2''': A new prompt <code>ap: </code> should appear in the console. Now type in the following commands as shown in the example:
<br/><br/>
 
 
<code>
 
ap:   
 
ap: '''ether_init'''
 
Initializing ethernet port 0...
 
Ethernet speed is 100 Mb - FULL Duplex
 
ap: '''load_helper'''
 
ap: '''reset'''
 
Are you sure you want to reset the system (y/n)?'''y'''
 
System resetting...
 
 
IOS Bootloader - Starting system.
 
flash is writable
 
FLASH CHIP:  Macronix Mirrorbit (00C2)
 
Xmodem file system is available.
 
 
''...''
 
</code>
 
  
 +
 +
ap:   
 +
ap: '''ether_init'''
 +
Initializing ethernet port 0...
 +
Ethernet speed is 100 Mb - FULL Duplex
 +
ap: '''load_helper'''
 +
ap: '''reset'''
 +
Are you sure you want to reset the system (y/n)?'''y'''
 +
System resetting...
 +
 +
IOS Bootloader - Starting system.
 +
flash is writable
 +
FLASH CHIP:  Macronix Mirrorbit (00C2)
 +
Xmodem file system is available.
 +
 +
''...''
 +
  
 
'''Step 3''': Let the machine normally boot up this time. The default username and password after a reset should be '''Cisco'''[https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/9215-pwrec-2.html#resios]:
 
'''Step 3''': Let the machine normally boot up this time. The default username and password after a reset should be '''Cisco'''[https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/9215-pwrec-2.html#resios]:
<code>
+
User Access Verification
+
User Access Verification
 
+
Username: '''Cisco'''
+
Username: '''Cisco'''
Password: '''Cisco'''
+
Password: '''Cisco'''
 
+
AP''xxxx.xxxx.xxxx''>
+
AP''xxxx.xxxx.xxxx''>
 
 
</code>
 

Revision as of 10:26, 10 October 2019

Step 1: Hold the mode Button down for approximately 20 seconds while powering up the access point. The Indicator LED should end to be blinking in red

Step 2: A new prompt ap: should appear in the console. Now type in the following commands as shown in the example:


ap:     
ap: ether_init
Initializing ethernet port 0...
Ethernet speed is 100 Mb - FULL Duplex
ap: load_helper
ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...

IOS Bootloader - Starting system.
flash is writable
FLASH CHIP:  Macronix Mirrorbit (00C2)
Xmodem file system is available. 

...

Step 3: Let the machine normally boot up this time. The default username and password after a reset should be Cisco[1]:

User Access Verification

Username: Cisco
Password: Cisco

APxxxx.xxxx.xxxx>