Difference between revisions of "Password Recovery Procedure for the Cisco AIR-CAP2602I-E-K9"

From NesevoWiki
Jump to navigationJump to search
(Created page using the commands joerg found and I found on https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/9215-pwrec-2.html#resios)
 
m (Added Note)
 
(9 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
'''Step 1''': Hold the mode Button down for approximately 20 seconds while powering up the access point. The Indicator LED should end to be '''blinking in <span style="color: red;">red</span>'''   
+
'''Step 1''': Hold the mode Button down for approximately 20 seconds while powering up the access point. The Indicator LED should end to be '''<span style="color: red;">blinking in red</span>'''   
−
<br/><br/>
 
−
'''Step 2''': A new prompt <code>ap: </code> should appear in the console. Now type in the following commands as shown in the example:
 
 
<br/><br/>
 
<br/><br/>
 +
'''Step 2''': Issue the '''<code>ether_init</code>''' command:
 +
 
 +
ap: '''ether_init'''
 +
Initializing ethernet port 0...
 +
Ethernet speed is 100 Mb - FULL Duplex
 +
 +
'''Step 3''': Issue the '''<code>flash_init</code>''' command and the '''<code>load_helper</code>''' command:
 +
 +
If the Flash has already initialized, you see this:
 +
 +
ap: '''flash_init'''
 +
Initializing Flash...
 +
...The flash is already initialized.
 +
ap:
 +
 +
If the Flash has not initialized, you see this:
 +
 +
ap: flash_init
 +
Initializing Flash...
 +
flashfs[0]: 21 files, 2 directories
 +
flashfs[0]: 0 orphaned files, 0 orphaned directories
 +
flashfs[0]: Total bytes: 7741440
 +
flashfs[0]: Bytes used: 4499456
 +
flashfs[0]: Bytes available: 3241984
 +
flashfs[0]: flashfs fsck took 7 seconds.
 +
...done initializing flash.
 +
Boot Sector Filesystem (bs:) installed, fsid: 3
 +
Parameter Block Filesystem (pb:) installed, fsid: 4
 +
 +
Issue the '''<code>load_helper</code>''' command in order to load any boot helper images. Here is an example:
  
−
<code>
+
     ap: '''load_helper'''
−
ap:      
+
    ap:
−
ap: '''ether_init'''
 
−
Initializing ethernet port 0...
 
−
Ethernet speed is 100 Mb - FULL Duplex
 
−
ap: '''load_helper'''
 
−
ap: '''reset'''
 
−
Are you sure you want to reset the system (y/n)?'''y'''
 
−
System resetting...
 
  
−
IOS Bootloader - Starting system.
 
−
flash is writable
 
−
FLASH CHIP:  Macronix Mirrorbit (00C2)
 
−
Xmodem file system is available.
 
  
−
''...''
+
'''Step 4''': Issue the '''<code>reset</code>''' command followed by an '''<code>y</code>''' to approve the reset.
−
</code>
+
ap: '''reset'''
 +
Are you sure you want to reset the system (y/n)?'''y'''
 +
System resetting...
 +
 +
IOS Bootloader - Starting system.
 +
flash is writable
 +
FLASH CHIP:  Macronix Mirrorbit (00C2)
 +
Xmodem file system is available.
 +
 +
''...''
 +
  
 +
'''Step 5''': Let the machine normally boot up this time. The default username and password after a reset should be '''<code>Cisco</code>'''[https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/9215-pwrec-2.html#resios]:
 +
 +
User Access Verification
 +
 +
Username: '''Cisco'''
 +
Password: '''Cisco'''
 +
 +
AP''xxxx.xxxx.xxxx''>
  
−
'''Step 3''': Let the machine normally boot up this time. The default username and password after a reset should be '''Cisco'''[https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/9215-pwrec-2.html#resios]:
 
−
<code>
 
−
User Access Verification
 
  
−
Username: '''Cisco'''
 
−
Password: '''Cisco'''
 
  
−
AP''xxxx.xxxx.xxxx''>
 
  
−
</code>
+
'''Note''': I (Jonas) noticed that, on some Access Points? (of which i tested), it just resets and doesn't enter the ROMMON.

Latest revision as of 10:38, 14 October 2019

Step 1: Hold the mode Button down for approximately 20 seconds while powering up the access point. The Indicator LED should end to be blinking in red

Step 2: Issue the ether_init command: 

ap: ether_init
Initializing ethernet port 0...
Ethernet speed is 100 Mb - FULL Duplex

Step 3: Issue the flash_init command and the load_helper command:

If the Flash has already initialized, you see this: 

ap: flash_init
Initializing Flash...
...The flash is already initialized.
ap:

If the Flash has not initialized, you see this: 

ap: flash_init
Initializing Flash...
flashfs[0]: 21 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 4499456
flashfs[0]: Bytes available: 3241984
flashfs[0]: flashfs fsck took 7 seconds.
...done initializing flash.
Boot Sector Filesystem (bs:) installed, fsid: 3
Parameter Block Filesystem (pb:) installed, fsid: 4

Issue the load_helper command in order to load any boot helper images. Here is an example: 

   ap: load_helper
   ap:


Step 4: Issue the reset command followed by an y to approve the reset. 

ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...

IOS Bootloader - Starting system.
flash is writable
FLASH CHIP:  Macronix Mirrorbit (00C2)
Xmodem file system is available. 

...

Step 5: Let the machine normally boot up this time. The default username and password after a reset should be Cisco[1]: 

User Access Verification

Username: Cisco
Password: Cisco

APxxxx.xxxx.xxxx>



Note: I (Jonas) noticed that, on some Access Points? (of which i tested), it just resets and doesn't enter the ROMMON.

Retrieved from "http://wiki.nesevo.com/index.php?title=Password_Recovery_Procedure_for_the_Cisco_AIR-CAP2602I-E-K9&oldid=2884"