Difference between revisions of "Loading IOS on a WS-C4900M / loading IOS and configuring the management interface via VRF / virtual router forwarding"
(New page: 1) configuring an IP address on the management port interface FastEthernet1 ip vrf forwarding mgmtVrf ip address 192.168.0.240 255.255.255.0 speed auto duplex auto 2) ping to check i...) |
|||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | 1) | + | '''1) configure an IP address on the management port''' |
| − | interface FastEthernet1 | + | Switch>en<br/> |
| − | + | Switch#configure terminal<br/> | |
| − | + | Switch(config-if)#interface FastEthernet1<br/> | |
| − | + | Switch(config-if)#ip vrf forwarding mgmtVrf<br/> | |
| − | + | Switch(config-if)#ip address 192.168.0.240 255.255.255.0<br/> | |
| + | Switch(config-if)#speed auto<br/> | ||
| + | Switch(config-if)#duplex auto<br/> | ||
| + | Switch(config-if)#exit<br/> | ||
| + | Switch(config)#exit<br/> | ||
| + | Switch# | ||
| − | 2) ping to check if it works | + | '''2) ping to check if it works''' |
Switch#ping vrf mgmtVrf 192.168.0.127 | Switch#ping vrf mgmtVrf 192.168.0.127 | ||
| − | Type escape sequence to abort. | + | Type escape sequence to abort.<br/> |
Sending 5, 100-byte ICMP Echos to 192.168.0.127, timeout is 2 seconds: | Sending 5, 100-byte ICMP Echos to 192.168.0.127, timeout is 2 seconds: | ||
| − | !!!!! | + | !!!!!<br/> |
| − | Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Switch# | + | Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms<br/> |
| + | Switch#<br/> | ||
| − | 3) configure the management port as source for the TFTP | + | '''3) configure the management port as source for the TFTP''' |
| − | Switch#conf t | + | Switch#conf t<br/> |
| − | Enter configuration commands, one per line. End with CNTL/Z. | + | Enter configuration commands, one per line. End with CNTL/Z.<br/> |
| − | Switch(config)#ip tftp source-interface FastEthernet1 | + | Switch(config)#ip tftp source-interface FastEthernet1<br/> |
| + | Switch#exit<br/> | ||
| + | Switch#<br/> | ||
| + | '''4) copy the IOS''' | ||
| − | + | Switch#copy tftp: slot0:<br/> | |
| + | Address or name of remote host [192.168.0.127]?<br/> | ||
| + | Source filename [XYZ]?<br/> | ||
| + | Destination filename [XYZ]?<br/> | ||
| + | Accessing tftp://192.168.0.127/XYZ<br/> | ||
| − | + | '''it should load now......''' | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | it should load now...... | ||
Latest revision as of 10:27, 5 January 2011
1) configure an IP address on the management port
Switch>en
Switch#configure terminal
Switch(config-if)#interface FastEthernet1
Switch(config-if)#ip vrf forwarding mgmtVrf
Switch(config-if)#ip address 192.168.0.240 255.255.255.0
Switch(config-if)#speed auto
Switch(config-if)#duplex auto
Switch(config-if)#exit
Switch(config)#exit
Switch#
2) ping to check if it works
Switch#ping vrf mgmtVrf 192.168.0.127
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.127, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
Switch#
3) configure the management port as source for the TFTP
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#ip tftp source-interface FastEthernet1
Switch#exit
Switch#
4) copy the IOS
Switch#copy tftp: slot0:
Address or name of remote host [192.168.0.127]?
Source filename [XYZ]?
Destination filename [XYZ]?
Accessing tftp://192.168.0.127/XYZ
it should load now......
