Difference between revisions of "Loading IOS on a ME-3400G-12CS-A Switch"
(8 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
'''Step 1:''' | '''Step 1:''' | ||
− | Switch(config) | + | Switch(config): interface GigabitEthernet0/13 |
− | Switch(config-if) | + | Switch(config-if): port-type eni |
− | Switch(config-if) | + | Switch(config-if): exit |
− | Switch(config) | + | Switch(config): interface GigabitEthernet0/12 |
− | Switch(config-if) | + | Switch(config-if): port-type nni |
− | Switch(config-if) | + | Switch(config-if): exit |
− | Switch(config) | + | Switch(config): interface Vlan1 |
− | Switch(config-if) | + | Switch(config-if): ip address 10.0.01 255.255.255.0 |
− | Switch(config-if) | + | Switch(config-if): no ip route-cache |
− | Switch(config-if) | + | Switch(config-if): end |
− | Switch(config) | + | Switch(config): interface gigabitEthernet 0/12 |
− | Switch(config-if) | + | Switch(config-if): no shut |
'''Step 2:''' | '''Step 2:''' | ||
− | |||
− | Sending 5, 100-byte ICMP Echos to | + | Switch#ping 10.0.01 |
+ | |||
+ | Sending 5, 100-byte ICMP Echos to 10.0.02, timeout is 2 seconds: | ||
!!!!! | !!!!! | ||
Line 36: | Line 37: | ||
'''Step 3:''' | '''Step 3:''' | ||
+ | |||
Switch#format flash: | Switch#format flash: | ||
Line 56: | Line 58: | ||
Format of flash complete | Format of flash complete | ||
− | '''Step 4:''' | + | |
+ | '''Step 4:''' | ||
copy from tftp to flash | copy from tftp to flash | ||
switch#copy tftp: flash: | switch#copy tftp: flash: | ||
− | Address or name of remote host []? | + | Address or name of remote host []? 10.0.01 |
Source filename []? me340x-metroipaccessk9-mz.122-55.SE.bin | Source filename []? me340x-metroipaccessk9-mz.122-55.SE.bin | ||
Line 67: | Line 70: | ||
Destination filename [me340x-metroipaccessk9-mz.122-55.SE.bin]? | Destination filename [me340x-metroipaccessk9-mz.122-55.SE.bin]? | ||
− | Accessing tftp:// | + | Accessing tftp://10.0.01/me340x-metroipaccessk9-mz.122-55.SE.bin... |
− | Loading me340x-metroipaccessk9-mz.122-55.SE.bin from | + | Loading me340x-metroipaccessk9-mz.122-55.SE.bin from 10.0.01 (via Vlan1): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!O!!!!!!!!!!!!!! |
[OK - 12619566 bytes] | [OK - 12619566 bytes] | ||
Line 77: | Line 80: | ||
− | '''Step | + | '''Step 5:''' |
delete the config | delete the config | ||
Line 91: | Line 94: | ||
− | + | '''Step 6:''' | |
− | '''Step | ||
reload | reload |
Latest revision as of 10:37, 3 February 2011
Step 1:
Switch(config): interface GigabitEthernet0/13
Switch(config-if): port-type eni
Switch(config-if): exit
Switch(config): interface GigabitEthernet0/12
Switch(config-if): port-type nni
Switch(config-if): exit
Switch(config): interface Vlan1
Switch(config-if): ip address 10.0.01 255.255.255.0
Switch(config-if): no ip route-cache
Switch(config-if): end
Switch(config): interface gigabitEthernet 0/12
Switch(config-if): no shut
Step 2:
Switch#ping 10.0.01
Sending 5, 100-byte ICMP Echos to 10.0.02, timeout is 2 seconds: !!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/203/1007 ms
Step 3:
Switch#format flash:
Format operation may take a while. Continue? [confirm]
Format operation will destroy all data in "flash:". Continue? [confirm]
flashfs[1]: 0 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32514048
flashfs[1]: Bytes used: 1024
flashfs[1]: Bytes available: 32513024
flashfs[1]: flashfs fsck took 8 seconds.
Format of flash complete
Step 4:
copy from tftp to flash
switch#copy tftp: flash: Address or name of remote host []? 10.0.01
Source filename []? me340x-metroipaccessk9-mz.122-55.SE.bin
Destination filename [me340x-metroipaccessk9-mz.122-55.SE.bin]?
Accessing tftp://10.0.01/me340x-metroipaccessk9-mz.122-55.SE.bin...
Loading me340x-metroipaccessk9-mz.122-55.SE.bin from 10.0.01 (via Vlan1): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!O!!!!!!!!!!!!!! [OK - 12619566 bytes]
12619566 bytes copied in 171.447 secs (73606 bytes/sec)
Switch#
Step 5:
delete the config
Switch#wr erase
Erasing the nvram filesystem will remove all files! Continue? [confirm] hit enter [OK]
Erase of nvram: complete
Switch#
Step 6:
reload
Switch#reload
System configuration has been modified. Save? [yes/no]: no
Proceed with reload? [confirm] hit enter