Difference between revisions of "Delete / Erase / Change Password for the Cisco LightStream 1010 ATM Switch"
| Line 56: | Line 56: | ||
'''Step 1:''' Hit '''ctrl / break''' directly after powering up the router. | '''Step 1:''' Hit '''ctrl / break''' directly after powering up the router. | ||
<br/><br/> | <br/><br/> | ||
| − | '''Step 2''' | + | '''Step 2:''' Type: '''''confreg 0x2142''''' from rommon 1> |
<br/><br/> | <br/><br/> | ||
| − | '''Step 3''' | + | '''Step 3:''' Type: '''''reset''''' from rommon 2> |
<br/><br/> | <br/><br/> | ||
| − | '''Step 4''' | + | '''Step 4:''' Would you like to enter the initial configuration dialog? [yes/no]: answer '''''NO''''' |
<br/><br/> | <br/><br/> | ||
'''Step 5:''' Type '''enable''' at Router> | '''Step 5:''' Type '''enable''' at Router> | ||
| Line 72: | Line 72: | ||
'''Step 9:''' Type '''enable secret <password>''' in order to change the enable secret password or type '''NO ENABLE SECRET''' to remove the secret from router(config)#> | '''Step 9:''' Type '''enable secret <password>''' in order to change the enable secret password or type '''NO ENABLE SECRET''' to remove the secret from router(config)#> | ||
<br/><br/> | <br/><br/> | ||
| − | '''Step 10''' | + | '''Step 10:''' Type: '''''NO ENABLE PASSWORD''''' to remove the password from router (config)#> |
<br/><br/> | <br/><br/> | ||
'''Step 14:''' Type the '''no shutdown''' command on every interface that you use. | '''Step 14:''' Type the '''no shutdown''' command on every interface that you use. | ||
Revision as of 12:32, 29 July 2008
Note: This password recovery procedure works for the following Cisco products:
| * Cisco 806 | * Cisco 4700 | * Catalyst 2948G-L3 |
| * Cisco 827 | * Cisco AS5x00 | * Catalyst 4840G |
| * Cisco uBR900 | * Cisco 6x00 | * Catalyst 4908G-L3 |
| * Cisco 1003 | * Cisco 7000 (RSP7000) | * Catalyst 5500 (RSM) |
| * Cisco 1004 | * Cisco 7100 | * Catalyst 8510-CSR |
| * Cisco 1005 | * Cisco 7200 | * Catalyst 8510-MSR |
| * Cisco 1400 | * Cisco 7500 | * Catalyst 8540-CSR |
| * Cisco 1600 | * Cisco uBR7100 | * Catalyst 8540-MSR |
| * Cisco 1700 | * Cisco uBR7200 | * Cisco MC3810 |
| * Cisco 2600 | * Cisco uBR10000 | * Cisco NI-2 |
| * Cisco 3600 | * Cisco 12000 | * Cisco VG200 Analog Gateway |
| * Cisco 4500 | * Cisco LS1010 | * Route Processor Module |
Step 1: Hit ctrl / break directly after powering up the router.
Step 2: Type: confreg 0x2142 from rommon 1>
Step 3: Type: reset from rommon 2>
Step 4: Would you like to enter the initial configuration dialog? [yes/no]: answer NO
Step 5: Type enable at Router>
Step 6:Type configure memory or copy startup-config running-config.
Step 7: Type show running-config.
Step 8: Type configure terminal to change or remove the password from the router.
Step 9: Type enable secret <password> in order to change the enable secret password or type NO ENABLE SECRET to remove the secret from router(config)#>
Step 10: Type: NO ENABLE PASSWORD to remove the password from router (config)#>
Step 14: Type the no shutdown command on every interface that you use.
Step 12: Type config-register 0x2102. .
Step 13: Hit Ctrl / z or end to leave the configuration mode.
Step 14: Type write memory or copy running-config startup-config to save the changes.
