Difference between revisions of "Delete / Erase / Change Password for the Cisco LightStream 1010 ATM Switch"
(New page: '''Note''': This password recovery procedure works for the following Cisco products: {| {{Prettytable}} | * Cisco 806 | * Cisco 4700 | * Catalyst 2948G-L3 |- | * Cisco 827 | * Cisco AS5x...) |
|||
| Line 1: | Line 1: | ||
'''Note''': This password recovery procedure works for the following Cisco products: | '''Note''': This password recovery procedure works for the following Cisco products: | ||
| − | {| {{Prettytable}} | + | {| {{Prettytable}} |
| * Cisco 806 | | * Cisco 806 | ||
| Line 23: | Line 23: | ||
| * Catalyst 8510-CSR | | * Catalyst 8510-CSR | ||
|- | |- | ||
| − | + | | * Cisco 1005 | |
| − | + | | * Cisco 7200 | |
| − | + | | * Catalyst 8510-MSR | |
| − | + | |- | |
| − | + | | * Cisco 1400 | |
| − | + | | * Cisco 7500 | |
| − | + | | * Catalyst 8540-CSR | |
| − | + | |- | |
| − | + | | * Cisco 1600 | |
| − | + | | * Cisco uBR7100 | |
| − | + | | * Catalyst 8540-MSR | |
| − | + | |- | |
| − | + | | * Cisco 1700 | |
| − | + | | * Cisco uBR7200 | |
| − | + | | * Cisco MC3810 | |
| − | + | |- | |
| − | + | | * Cisco 2600 | |
| − | + | | * Cisco uBR10000 | |
| − | + | | * Cisco NI-2 | |
| − | + | |- | |
| − | + | | * Cisco 3600 | |
| − | + | | * Cisco 12000 | |
| − | + | | * Cisco VG200 Analog Gateway | |
| − | + | |- | |
| − | + | | * Cisco 4500 | |
| − | + | | * Cisco LS1010 | |
| − | + | | * Route Processor Module | |
| − | + | |} | |
| − | + | <br/><br/> | |
| − | + | <br/><br/> | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | '''Step 1:''' Hit '''ctrl / break''' directly after powering up the router. | |
| + | <br/><br/> | ||
| + | '''Step 2''': type: '''''confreg 0x2142''''' from rommon 1> | ||
| + | <br/><br/> | ||
| + | '''Step 3''': type: '''''reset''''' from rommon 2> | ||
| + | <br/><br/> | ||
| + | '''Step 4''': Would you like to enter the initial configuration dialog? [yes/no]: answer '''''NO''''' | ||
| + | <br/><br/> | ||
| + | '''Step 5:''' Type '''enable''' at Router> | ||
| + | <br/><br/> | ||
| + | '''Step 6:'''Type '''configure memory or copy startup-config running-config'''. | ||
| + | <br/><br/> | ||
| + | '''Step 7:''' Type '''show running-config'''. | ||
| + | <br/><br/> | ||
| + | '''Step 8:''' Type '''configure terminal''' to change or remove the password from the router. | ||
| + | <br/><br/> | ||
| + | '''Step 9:''' Type '''enable secret <password>''' in order to change the enable secret password or type '''NO ENABLE SECRET''' to remove the secret from router(config)#> | ||
| + | <br/><br/> | ||
| + | '''Step 10''': type: '''''NO ENABLE PASSWORD''''' to remove the password from router (config)#> | ||
| + | <br/><br/> | ||
| + | '''Step 14:''' Type the '''no shutdown''' command on every interface that you use. | ||
| + | <br/><br/> | ||
| + | '''Step 12:''' Type '''config-register 0x2102.''' . | ||
| + | <br/><br/> | ||
| + | '''Step 13:''' Hit '''Ctrl / z''' or '''end''' to leave the configuration mode. | ||
| + | <br/><br/> | ||
| + | '''Step 14:''' Type ''' write memory''' or '''copy running-config startup-config ''' to save the changes. | ||
| + | <br/><br/> | ||
Revision as of 09:32, 29 July 2008
Note: This password recovery procedure works for the following Cisco products:
| * Cisco 806 | * Cisco 4700 | * Catalyst 2948G-L3 |
| * Cisco 827 | * Cisco AS5x00 | * Catalyst 4840G |
| * Cisco uBR900 | * Cisco 6x00 | * Catalyst 4908G-L3 |
| * Cisco 1003 | * Cisco 7000 (RSP7000) | * Catalyst 5500 (RSM) |
| * Cisco 1004 | * Cisco 7100 | * Catalyst 8510-CSR |
| * Cisco 1005 | * Cisco 7200 | * Catalyst 8510-MSR |
| * Cisco 1400 | * Cisco 7500 | * Catalyst 8540-CSR |
| * Cisco 1600 | * Cisco uBR7100 | * Catalyst 8540-MSR |
| * Cisco 1700 | * Cisco uBR7200 | * Cisco MC3810 |
| * Cisco 2600 | * Cisco uBR10000 | * Cisco NI-2 |
| * Cisco 3600 | * Cisco 12000 | * Cisco VG200 Analog Gateway |
| * Cisco 4500 | * Cisco LS1010 | * Route Processor Module |
Step 1: Hit ctrl / break directly after powering up the router.
Step 2: type: confreg 0x2142 from rommon 1>
Step 3: type: reset from rommon 2>
Step 4: Would you like to enter the initial configuration dialog? [yes/no]: answer NO
Step 5: Type enable at Router>
Step 6:Type configure memory or copy startup-config running-config.
Step 7: Type show running-config.
Step 8: Type configure terminal to change or remove the password from the router.
Step 9: Type enable secret <password> in order to change the enable secret password or type NO ENABLE SECRET to remove the secret from router(config)#>
Step 10: type: NO ENABLE PASSWORD to remove the password from router (config)#>
Step 14: Type the no shutdown command on every interface that you use.
Step 12: Type config-register 0x2102. .
Step 13: Hit Ctrl / z or end to leave the configuration mode.
Step 14: Type write memory or copy running-config startup-config to save the changes.
