Cisco7609 and Cisco7609-S routers

From NesevoWiki
Revision as of 09:05, 13 May 2008 by Stephan (talk | contribs)
Jump to navigationJump to search

Supervisor engines

Both, the Cisco7609 and the Cisco7609-S router have nine vertical slots being numbered from right to left and measure 21 rack units (21 RU).
While the supported supervisor engine 2 (see below) is installed in slot 1 and an optional redundant supervisor engine 2 in slot 2, the supported supervisor engine 720, supervisor engine 32 and route switch processor 720 are installed in slot 5 (first supervisor engine)and slot 6 (optional redundant supervisor engine).
!!! Note: When installing a redundant supervisor engine, both supervisor engines must be identical.
!!! Note: The GBIC uplink ports are fully functional on the redundant supervisor engine in stand by.
If a redundant supervisor engine is not required, all free slots can be equipped with any supported cisco7600 series / catalyst 6500 series module.

Supported supervisor engines in the Cisco7609 router

  • Supervisor engine 2
    !!! To be installed in slot 1 (first supervisor engine) and in slot 2 (optional redundant supervisor engine).
    • WS-X6K-S2-PFC2
    • WS-X6K-S2-MSFC2
    • WS-X6K-S2U-MSFC2
  • Supervisor engine 720
    !!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
    • WS-SUP720
    • WS-SUP720-3B
    • WS-SUP720-3BXL

!!!Note: The Supervisor Enigne 720 has two GBIC uplink ports and one 10/100/1000 Tx port. Only two of the three ports can be active at any one time.

  • Supervisor engine 32
    !!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
    • WS-SUP32-GE-3B
    • WS-SUP32-10GE-3B
  • Route switch processor 720
    !!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
    • RSP720-3C-GE
    • RSP720-3CXL-GE

Supported supervisor engines in the Cisco7609-S router

  • Supervisor engine 32
    !!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
    • WS-SUP32-GE-3B
    • WS-SUP32-10GE-3B
  • Supervisor engine 720
    !!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
    • WS-SUP720
    • WS-SUP720-3B
    • WS-SUP720-3BXL
  • Route switch processor 720
    !!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
    • RSP720-3C-GE
    • RSP720-3CXL-GE

!!! Note: the supervisor engine 2 is not longer supported in the Cisco7609-S router.

Power supplies and power entry modules

Both, the Cisco7606 and the Cisco7606-S router have two power supply slots on the back of the chassis, with the power supply 1 being installed on the bottom and the optional redundant power supply 2 being installed in the upper of the two slots.

Supported power supplies in the Cisco7609 router

  • 2500 watt DC-input power supply
    • WS-CDC-2500W

No power entry module is needed when using a WS-CDC-2500W

  • 3000 watt AC-input power supply
    • WS-CAC-3000W

No power entry module is needed when using a WS-CAC-3000W

  • 4000 watt AC-input power supply
    • WS-CAC-4000W-US1

No power entry module is needed when using a WS-CAC-4000W-US1/6

  • 4000 watt DC-input power supply
    • PWR-4000-DC

No power entry module is needed when using a PWR-4000-DC

  • 6000 watt AC-input power supply
    • WS-CAC-6000W

No power entry module is needed when using a WS-CAC-6000W

  • 6000 watt DC-input power supply
    • PWR-6000-DC

No power entry module is needed when using a PWR-6000-DC

Supported power supplies in the Cisco7609-S router

  • 4000 watt AC-input power supply
    • WS-CAC-4000W-US1

No power entry module is needed when using a WS-CAC-4000W-US1/6

  • 4000 watt DC-input power supply
    • PWR-4000-DC

No power entry module is needed when using a PWR-4000-DC

  • 6000 watt AC-input power supply
    • WS-CAC-6000W

No power entry module is needed when using a WS-CAC-6000W

  • 6000 watt DC-input power supply
    • PWR-6000-DC

No power entry module is needed when using a PWR-6000-DC

Fan trays

Supported fan trays in the Cisco7606 router

  • standard fan module
    • WS-C6K-6SLOT-FAN
  • high speed fan module
    • FAN-MOD-6HS

!!! Note: supervisor engine 720 configurations require the FAN-MOD-6HS. WS-C6K-6SLOT-FAN will only work in supervisor engine 2 configurations.

Supported fan trays in the Cisco7606-S router

  • high speed fan module
    • FAN-MOD-6SHS

!!! Note: As a result of the sup 32 being the minimum required supervisor engine for the Cisco7606-S, no standard fan tray is supported in any cisco7606-S configuration. Both high speed fans, the FAN-MOD-6SHS and the FAN-MOD-6HS will work in the Cisco7606-S. With the FAN-MOD-6SHS being white, the colour would be the only difference.

Retrieved from "http://wiki.nesevo.com/index.php?title=Cisco7609_and_Cisco7609-S_routers&oldid=184"