Difference between revisions of "Cabling and Configuring Opengear CM4148"
From NesevoWiki
Jump to navigationJump to search| Line 43: | Line 43: | ||
* For Opengear equipment with a RJ45 console port | * For Opengear equipment with a RJ45 console port | ||
** again, make sure port is configured like this | ** again, make sure port is configured like this | ||
| − | ** <code>Baud Rate: 115200</code> | + | *** <code>Baud Rate: 115200</code> |
| − | ** <code>Data Bits: 8</code> | + | *** <code>Data Bits: 8</code> |
| − | ** <code>Parity: None</code> | + | *** <code>Parity: None</code> |
| − | ** <code>Stop Bits: 1</code> | + | *** <code>Stop Bits: 1</code> |
| − | ** <code>Flow Control: None</code> | + | *** <code>Flow Control: None</code> |
| − | * Console Server Settings | + | ** Console Server Settings |
| − | ** Activate Console Server Mode | + | *** Activate Console Server Mode |
| − | ** Activate SSH (or other protocols you want to use) | + | *** Activate SSH (or other protocols you want to use) |
** Use an RJ45 - RJ45 rollover cable, these are usually easily identified as light blue and flat – however are not included with your Opengear device | ** Use an RJ45 - RJ45 rollover cable, these are usually easily identified as light blue and flat – however are not included with your Opengear device | ||
Revision as of 08:41, 4 December 2018
Connecting Cisco Network Equipment
Configuration of Serial Ports
- Common Settings
Baud Rate: 9600Data Bits: 8Parity: NoneStop Bits: 1Flow Control: None
- Console Server Settings
- Activate Console Server Mode
- Activate SSH (or other protocols you want to use)
Cabling
- Plug Opengear's Cisco specific adapter Cable (Opengear PartNo 449016) into the Cisco device's console port (do not plug it into the console server's (CM4148) serial port, that won't work!)
- Use a common, straight ethernet patch cable to connect the console server's serial port to the socket of the adapter cable.
Connecting Opengear Local Consoles
To connect another Opengear device via it's local console.
Configuration of Serial Ports
- Common Settings
Baud Rate: 115200Data Bits: 8Parity: NoneStop Bits: 1Flow Control: None
- Console Server Settings
- Activate Console Server Mode
- Activate SSH (or other protocols you want to use)
Cabling
- For Opengear equipment with a DB9 console port
- Alternative 1
- Plug the DB9-to-RJ45 adaptor (Opengear PartNo 319000, the straight variant, not the cross-over one!) into the devices console port.
- Use one of the typical light blue Cisco (!) console cables to connect the console server's (CM4148) serial port to the DB9-connector.
- Alternative 2
- Plug the DB9-to-RJ45 adaptor (Opengear PartNo 319001, the crossover variant, not the straight one!) into the devices console port.
- Take a common straight ethernet patch cable to connect the console server's (CM4148) serial port to the DB9-connector.
- Alternative 3
- Plug the DB9-to-RJ45 adaptor (PartNo 74-0495-01) into the devices console port.
- Plug the Cisco specific Opengear adaptor cable (Opengear PartNo 449016) into the DB9-to-RJ45 adaptor.
- Take a common straight ethernet patch cable to connect the console server's (CM4148) serial port to the Cisco specific Opengear adaptor cable.
- Alternative 1
- For Opengear equipment with a RJ45 console port
- again, make sure port is configured like this
Baud Rate: 115200Data Bits: 8Parity: NoneStop Bits: 1Flow Control: None
- Console Server Settings
- Activate Console Server Mode
- Activate SSH (or other protocols you want to use)
- Use an RJ45 - RJ45 rollover cable, these are usually easily identified as light blue and flat – however are not included with your Opengear device
- again, make sure port is configured like this
- TODO
Connecting ALIX Mini PC Local Consoles
Configuration of Serial Ports
- Common Settings
Baud Rate: 38400Data Bits: 8Parity: NoneStop Bits: 1Flow Control: None
- Console Server Settings
- Activate Console Server Mode
- Activate SSH (or other protocols you want to use)
Cabling
- Plug the DB9-connector (Opengear PartNo 319001, the x-over variant, not the straight one!) into the devices console port.
- Use a common straight ethernet patch cable to connect the console server's (CM4148) serial port to the DB9-connector.
Connecting via SSH
- Connect via SSH to
<IP of console server>on port3000 + <PortNo>. If your console server has the IP address of 192.168.3.3 and your device is connected to port 25, then connect via SSH to192.168.3.3:3025using the user name and password you configured.
