Difference between revisions of "Cisco7609 and Cisco7609-S routers"
(New page: ==Supervisor engines== Both, the Cisco7609 and the Cisco7609-S router have nine vertical slots being numbered from right to left and measure 21 rack units (21 RU).<br/> While the supported...) |
|||
| Line 24: | Line 24: | ||
**WS-SUP32-10GE-3B<br/> | **WS-SUP32-10GE-3B<br/> | ||
| − | ''!!! | + | *Route switch processor 720<br/>''!!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).''<br/> |
| + | **RSP720-3C-GE<br/> | ||
| + | **RSP720-3CXL-GE<br/> | ||
'''Supported supervisor engines in the Cisco7606-S router'''<br/> | '''Supported supervisor engines in the Cisco7606-S router'''<br/> | ||
Revision as of 08:49, 13 May 2008
Supervisor engines
Both, the Cisco7609 and the Cisco7609-S router have nine vertical slots being numbered from right to left and measure 21 rack units (21 RU).
While the supported supervisor engine 2 (see below) is installed in slot 1 and an optional redundant supervisor engine 2 in slot 2, the supported supervisor engine 720, supervisor engine 32 and route switch processor 720 are installed in slot 5 (first supervisor engine)and slot 6 (optional redundant supervisor engine).
!!! Note: When installing a redundant supervisor engine, both supervisor engines must be identical.
!!! Note: The GBIC uplink ports are fully functional on the redundant supervisor engine in stand by.
If a redundant supervisor engine is not required, all free slots can be equipped with any supported cisco7600 series / catalyst 6500 series module.
Supported supervisor engines in the Cisco7609 router
- Supervisor engine 2
!!! To be installed in slot 1 (first supervisor engine) and in slot 2 (optional redundant supervisor engine).
- WS-X6K-S2-PFC2
- WS-X6K-S2-MSFC2
- WS-X6K-S2U-MSFC2
- WS-X6K-S2-PFC2
- Supervisor engine 720
!!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
- WS-SUP720
- WS-SUP720-3B
- WS-SUP720-3BXL
- WS-SUP720
!!!Note: The Supervisor Enigne 720 has two GBIC uplink ports and one 10/100/1000 Tx port. Only two of the three ports can be active at any one time.
- Supervisor engine 32
!!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
- WS-SUP32-GE-3B
- WS-SUP32-10GE-3B
- WS-SUP32-GE-3B
- Route switch processor 720
!!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
- RSP720-3C-GE
- RSP720-3CXL-GE
- RSP720-3C-GE
Supported supervisor engines in the Cisco7606-S router
- Supervisor engine 32
!!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
- WS-SUP32-GE-3B
- WS-SUP32-10GE-3B
- WS-SUP32-GE-3B
- Supervisor engine 720
!!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
- WS-SUP720
- WS-SUP720-3B
- WS-SUP720-3BXL
- WS-SUP720
- Route switch processor 720
!!! To be installed in slot 5 (first supervisor engine) and in slot 6 (optional redundant supervisor engine).
- RSP720-3C-GE
- RSP720-3CXL-GE
- RSP720-3C-GE
!!! Note: the supervisor engine 2 is not longer supported in the Cisco7606-S router.
Power supplies and power entry modules
Both, the Cisco7606 and the Cisco7606-S router have two power supply slots on the back of the chassis, with the power supply 1 being installed on the bottom and the optional redundant power supply 2 being installed in the upper of the two slots.
Supported power supplies in the Cisco7606 router
- 1900 watt AC-input power supply
- PWR-1900-AC/6
- PWR-1900-AC/6
!!! Note: the power entry module PEM-20A-AC is needed when using a PWR-1900-AC/6. You need one PEM-20A-AC per PWR-1900-AC/6.
The power entry modules are installed on the front of the chassis on the very top.
- 1900 watt DC-input power supply
- PWR-1900-DC
- PWR-1900-DC
!!! Note: the power entry module PEM-DC is needed when using a PWR-1900-DC. You need one PEM-DC per PWR-1900-DC.
The power entry modules are installed on the front of the chassis on the very top.
- 2700 watt AC-input power supply
- PWR-2700-AC
- PWR-2700-AC
No power entry module is needed when using a PWR-2700-AC
- 2700 watt DC-input power supply
- PWR-2700-DC
- PWR-2700-DC
No power entry module is needed when using a PWR-2700-DC
Supported power supplies in the Cisco7606-S router
- 2700 watt AC-input power supply
- PWR-2700-AC
- PWR-2700-AC
No power entry module is needed when using a PWR-2700-AC
- 2700 watt DC-input power supply
- PWR-2700-DC
- PWR-2700-DC
No power entry module is needed when using a PWR-2700-DC
Fan trays
Supported fan trays in the Cisco7606 router
- standard fan module
- WS-C6K-6SLOT-FAN
- WS-C6K-6SLOT-FAN
- high speed fan module
- FAN-MOD-6HS
- FAN-MOD-6HS
!!! Note: supervisor engine 720 configurations require the FAN-MOD-6HS. WS-C6K-6SLOT-FAN will only work in supervisor engine 2 configurations.
Supported fan trays in the Cisco7606-S router
- high speed fan module
- FAN-MOD-6SHS
- FAN-MOD-6SHS
!!! Note: As a result of the sup 32 being the minimum required supervisor engine for the Cisco7606-S, no standard fan tray is supported in any cisco7606-S configuration. Both high speed fans, the FAN-MOD-6SHS and the FAN-MOD-6HS will work in the Cisco7606-S. With the FAN-MOD-6SHS being white, the colour would be the only difference.
