Difference between revisions of "Password recovery & checking / installing licenses"

Latest revision as of 16:50, 21 December 2017

visit ->support.riverbed.com/content/support/licensing.htm
enter the serial number of your device and click next
all the licenses with their keys linked to your device are listed on a new page. Use this list for copy & paste license names.
Connect to the Riverbed CLI
if necessary, you can wipe the existing config by doing the following
login with user:admin and password:password and do a factory reset

note: this is only recommended for experienced users

Enter enable mode; at the system prompt, enter the enable command: amnesiac > enable
Enter enable mode; at the system prompt, enter the enable command: amnesiac > reset factory
confirm & wait until the device reboots
log in again with admin & password
Enter enable mode; at the system prompt, enter the enable command: amnesiac > enable
Enter configuration mode; at the system prompt, enter the configure terminal command:amnesiac # configure terminal
View current and available model specifications; enter the show hardware spec command:

amnesiac (config) # show hardware spec

  Spec       Description
- ---------- ----------------------------------------------------------------------
  1050_LR      BW Limit: 8000 Kb/s      Connection Limit: 800
         (activation requires hardware)
  1050_MR      BW Limit: 10000 Kb/s     Connection Limit: 1300
       (activation requires hardware)
* 1050H        BW Limit: 20000 Kb/s     Connection Limit: 2300
       (activation requires hardware)
  1050_HR      BW Limit: 20000 Kb/s     Connection Limit: 2300
       (activation requires hardware)
* = active

Install the model upgrade license; enter the license install <license-key> command:

amnesiac (config) # license install LIC-EXAMPLE-1050H-0000-0000-0-000X-0XX0

Write the model upgrade license to memory; enter the write memory command:

amnesiac (config) # write memory

View licenses installed on the appliance; enter the show licenses command:

amnesiac (config) # show licenses

LIC-EXAMPLE-1050H-0000-0000-0-000X-0XX0
Index: 6
Feature: MSPECEX1050H
Valid: yes
active: yes

repeat this for every license you want to activate

if you want to change the specification of your device, view the available model upgrade specification; enter the show hardware spec command:

amnesiac (config) # show hardware spec

Spec       Description
- ---------- ----------------------------------------------------------------------
  1050_LR      BW Limit: 8000 Kb/s      Connection Limit: 800
         (activation requires hardware)
  1050_MR      BW Limit: 10000 Kb/s     Connection Limit: 1300
       (activation requires hardware)
* 1050H        BW Limit: 20000 Kb/s     Connection Limit: 2300
       (activation requires hardware)
  1050_HR      BW Limit: 20000 Kb/s     Connection Limit: 2300
       (activation requires hardware)
* = active

Stop the optimization service; enter the no service enable command:

amnesiac (config) # no service enable

Terminating optimization service.......

Activate the desired model specification; enter the hardware spec activate <model-number> command:

amnesiac (config) # hardware spec activate <model-number>

Appliance upgrade to <model-number> successful

Note: 
Upgrades that require additional hardware automatically shut down the appliance after you activate the model upgrade specification. 
Install the new hardware and power on the system. The system reformats the drives and completes the upgrade.

Restart the optimization service for model upgrades that do not require a reboot, enter the restart command:

amnesiac (config) # restart

Terminating optimization service......
Relaunching optimization service.

@@ Line 1: / Line 1: @@
+[http://www.example.com link title]
+* visit [https://support.riverbed.com/content/support/licensing.html ->support.riverbed.com/content/support/licensing.htm]
+* enter the serial number of your device and click next
+* all the licenses with their keys linked to your device are listed on a new page. Use this list for copy & paste license names.
 * Connect to the Riverbed CLI
+* if necessary, you can wipe the existing config by doing the following
+* login with user:<code>admin</code> and password:<code>password</code> and do a factory reset
+ note: this is only recommended for experienced users
+* Enter enable mode; at the system prompt, enter the enable command: <code>amnesiac > enable</code>
+* Enter enable mode; at the system prompt, enter the enable command: <code>amnesiac > reset factory</code>
+* confirm & wait until the device reboots
+* log in again with admin & password
 * Enter enable mode; at the system prompt, enter the enable command: <code>amnesiac > enable</code>
 * Enter configuration mode; at the system prompt, enter the configure terminal command:<code>amnesiac # configure terminal</code>
 * View current and available model specifications; enter the show hardware spec command:
+<code>amnesiac (config) # show hardware spec</code>
+   Spec       Description
+ - ---------- ----------------------------------------------------------------------
+_LR      BW Limit: 8000 Kb/s      Connection Limit: 800
+          (activation requires hardware)
+_MR      BW Limit: 10000 Kb/s     Connection Limit: 1300
+        (activation requires hardware)
+ * 1050H        BW Limit: 20000 Kb/s     Connection Limit: 2300
+        (activation requires hardware)
+_HR      BW Limit: 20000 Kb/s     Connection Limit: 2300
+        (activation requires hardware)
+ * = active
+<br>
+* Install the model upgrade license; enter the license install <license-key> command: <br>
+<code>amnesiac (config) # license install LIC-EXAMPLE-1050H-0000-0000-0-000X-0XX0</code>
+* Write the model upgrade license to memory; enter the write memory command:
+<code>amnesiac (config) # write memory</code>
+* View licenses installed on the appliance; enter the show licenses command:
+<code>amnesiac (config) # show licenses</code>
+ LIC-EXAMPLE-1050H-0000-0000-0-000X-0XX0
+ Index: 6
+ Feature: MSPECEX1050H
+ Valid: yes
+ active: yes
+<br>
+* repeat this for every license you want to activate
 <br>
-<code>amnesiac (config) # show hardware spec<br>
+* if you want to change the specification of your device, view the available model upgrade specification; enter the show hardware spec command:
-Spec Description<br>
+<code>amnesiac (config) # show hardware spec</code>
+ Spec       Description
+ - ---------- ----------------------------------------------------------------------
+_LR      BW Limit: 8000 Kb/s      Connection Limit: 800
+          (activation requires hardware)
+_MR      BW Limit: 10000 Kb/s     Connection Limit: 1300
+        (activation requires hardware)
+ * 1050H        BW Limit: 20000 Kb/s     Connection Limit: 2300
+        (activation requires hardware)
+_HR      BW Limit: 20000 Kb/s     Connection Limit: 2300
+        (activation requires hardware)
+ * = active
+* Stop the optimization service; enter the no service enable command:
+<code>amnesiac (config) # no service enable</code>
+ Terminating optimization service.......
+* Activate the desired model specification; enter the hardware spec activate <model-number> command:
+<code>amnesiac (config) # hardware spec activate <model-number></code>
+ Appliance upgrade to <model-number> successful<br>
-* EX760L BW Limit: 10000 Kb/s Connection Limit: 900<br>
+ Note:
+  Upgrades that require additional hardware automatically shut down the appliance after you activate the model upgrade specification.
-EX760M BW Limit: 10000 Kb/s Connection Limit: 1500<br>
+ Install the new hardware and power on the system. The system reformats the drives and completes the upgrade.
-(activation requires license)<br>
-EX760H BW Limit: 20000 Kb/s Connection Limit: 2300<br>
+*Restart the optimization service for model upgrades that do not require a reboot, enter the restart command:
-(activation requires license)<br>
+<code>amnesiac (config) # restart</code>
-* = active<br>
+ Terminating optimization service......
-</code>
+ Relaunching optimization service.
-<br>
-* this will give out a huge diagnostic report, some seconds after the section  <code>=====display interface====</code> appears, stop the output by pressing <code>CTRL + C</code>
-* now search for the entry which starts with <code>IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is xxxx-xxxx-xxxx</code>
-* the <code>xxxx-xxxx-xxxx</code> part is the Base Mac-adress of the device

Difference between revisions of "Password recovery & checking / installing licenses"

Latest revision as of 16:50, 21 December 2017

Navigation menu

Page actions

Page actions

Personal tools

Navigation

Search

Tools