SFP/QSFP Compatibility Matrix - Revision history

Philipp: /* Test Results */

2021-05-20T07:43:09Z

Test Results

Philipp: /* Edgecore */

2021-05-20T07:39:35Z

Edgecore

Philipp: /* Edgecore */

2021-05-20T07:34:14Z

Edgecore

Philipp at 07:08, 20 May 2021

2021-05-20T07:08:24Z

Philipp at 14:49, 18 May 2021

2021-05-18T14:49:25Z

Lager: initial ad-hoc made version

2021-05-18T13:58:29Z

initial ad-hoc made version

New page

== Setup ==

* 2 Laptops configured with an IP in an chosen Subnet.
* 2 Switches connected using the same SFP on both sides.
* One Laptop connected to the first switch, and the other one connected to the other switch.

=== Edgecore ===

Additionally needed steps for Edgecore (Rolled back using <code>sudo mv /etc/network/interfaces.bak /etc/network/interfaces</code> and <code>sudo ifreload --all</code>):

* <code>cp /etc/network/interfaces /etc/network/interfaces.bak</code>
* <code>sudo nano etc/network/interfaces</code>

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

source /etc/network/interfaces.d/*.intf

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
auto eth0
iface eth0 inet dhcp

auto vlan
iface vlan
bridge-vlan-aware yes
bridge-ports glob swp1-54
bridge-stp on

* <code>sudo ifreload --all</code>

== Test Results ==

{| class="wikitable"
!Switch Manufacturer
!Switch PN
!SFP PN
!Kabel-Typ
!Modul-Typ
!SFP EEPROM Erkannt
!Interface Auto Up
!Cross-Switch-Ping
!Firmware
|-
|Quanta
|T1048-LY4R
|GLC-SX-MM
|LC/PC-LC/PC-MM
|Multi Mode SFP
|OK
|NO
|NA
|Cumulus Linux 3.7.2
|-
|Quanta
|T1048-LY4R
|SFP-10G-SR
|LC/PC-LC/PC-MM
|Multi Mode SFP
|OK
|YES
|OK
|Cumulus Linux 3.7.2
|-
|Quanta
|T1048-LY4R
|GLC-LH-SM
|LC/PC-LC/PC-SM
|Single Mode SFP
|OK
|NO
|NA
|Cumulus Linux 3.7.2
|-
|Quanta
|T1048-LY4R
|SFP-10G-LR
|LC/PC-LC/PC-MM
|Multi Mode SFP
|OK
|YES
|OK
|Cumulus Linux 3.7.2
|-
|Edgecore
|CX-4048-T-R-B
|QSFP-40G-SR4
|MPO OM4
|Single Mode QSFP
|OK
|YES
|OK
|Cumulus Linux 3.7.13
|-
|Edgecore
|CX-4048-T-R-B
|QSFP-40G-UNIV
|LC/PC-LC/PC-MM
|Multi Mode QSFP
|OK
|YES
|OK
|Cumulus Linux 3.7.13
|-
|Edgecore
|CX-4048-T-R-B
|AQOMLBQ4EDNA0882
|MPO OM4
|? QSFP
|OK
|YES
|OK
|Cumulus Linux 3.7.13
|}

=== Commands used ===

sudo ethtool --dump-module-eeprom swp49

net show interface all | grep "swp49" -A 4

ip link show swp49

← Older revision		Revision as of 07:39, 20 May 2021
Line 36:		Line 36:

	* <code>sudo ifreload --all</code>		* <code>sudo ifreload --all</code>
		+
		+	=== Quanta ===
		+
		+	* The default speed of the SFP ports is 10000
		+	* For 1G modules, you have to set it to 1000
		+	* Use the following commands:
		+	** <code>net add interface swp49 link speed 1000</code>
		+	** <code>net commit</code>
		+	* These commands will edit the <code>/etc/network/interfaces</code> file and apply the config.

	== Test Results ==		== Test Results ==

@@ Line 58: / Line 58: @@
 !Cross-Switch-Ping
 !Firmware
 |-
 |Quanta
@@ Line 65: / Line 66: @@
 |Multi Mode SFP
 |OK
-|NO
+|YES
-|NA
+|OK
 |Cumulus Linux 3.7.2
 |-
 |Quanta
@@ Line 78: / Line 80: @@
 |OK
 |Cumulus Linux 3.7.2
 |-
 |Quanta
@@ Line 85: / Line 88: @@
 |Single Mode SFP
 |OK
-|NO
+|YES
-|NA
+|OK
 |Cumulus Linux 3.7.2
 |-
 |Quanta
@@ Line 98: / Line 102: @@
 |OK
 |Cumulus Linux 3.7.2
 |-
 |Edgecore
@@ Line 108: / Line 113: @@
 |OK
 |Cumulus Linux 3.7.13
 |-
 |Edgecore
@@ Line 118: / Line 124: @@
 |OK
 |Cumulus Linux 3.7.13
 |-
 |Edgecore
@@ Line 128: / Line 135: @@
 |OK
 |Cumulus Linux 3.7.13
 |}

@@ Line 29: / Line 29: @@
   iface eth0 inet dhcp
-  auto vlan
+  '''auto vlan'''
-  iface vlan
+  '''iface vlan'''
-       bridge-vlan-aware yes
+       '''bridge-vlan-aware yes'''
-       bridge-ports glob swp1-54
+       '''bridge-ports glob swp1-54'''
-       bridge-stp on
+       '''bridge-stp on'''
 * <code>sudo ifreload --all</code>

@@ Line 6: / Line 6: @@
 * 2 Switches connected using the same SFP on both sides.
 * One Laptop connected to the first switch, and the other one connected to the other switch.
 === Edgecore ===

@@ Line 51: / Line 51: @@
 |Quanta
 |T1048-LY4R
-|GLC-SX-MM
+|GLC-SX-MM (3rd Party, Cisco-Compatible)
 |LC/PC-LC/PC-MM
 |Multi Mode SFP
@@ Line 61: / Line 61: @@
 |Quanta
 |T1048-LY4R
-|SFP-10G-SR
+|SFP-10G-SR (3rd Party, Cisco-Compatible)
 |LC/PC-LC/PC-MM
 |Multi Mode SFP
@@ Line 71: / Line 71: @@
 |Quanta
 |T1048-LY4R
-|GLC-LH-SM
+|GLC-LH-SM (3rd Party, Cisco-Compatible)
 |LC/PC-LC/PC-SM
 |Single Mode SFP
@@ Line 81: / Line 81: @@
 |Quanta
 |T1048-LY4R
-|SFP-10G-LR
+|SFP-10G-LR (3rd Party, Cisco-Compatible)
 |LC/PC-LC/PC-MM
 |Multi Mode SFP
@@ Line 91: / Line 91: @@
 |Edgecore
 |CX-4048-T-R-B
-|QSFP-40G-SR4
+|QSFP-40G-SR4 (3rd Party, Cisco-Compatible)
 |MPO OM4
 |Single Mode QSFP
@@ Line 101: / Line 101: @@
 |Edgecore
 |CX-4048-T-R-B
-|QSFP-40G-UNIV
+|QSFP-40G-UNIV (3rd Party, Cisco-Compatible)
 |LC/PC-LC/PC-MM
 |Multi Mode QSFP
@@ Line 111: / Line 111: @@
 |Edgecore
 |CX-4048-T-R-B
-|AQOMLBQ4EDNA0882
+|AQOMLBQ4EDNA0882 (3rd Party, Cisco-Compatible)
 |MPO OM4
 |? QSFP