View source for Cisco7603 and Cisco7603-S routers

'''NOT supported hardware in cisco7603 chassis'''<br/>
–WS-X6704-10GE—4-port 10-Gigabit Ethernet XENPAK <br/>
–WS-X6748-SFP—48-port Gigabit Ethernet SFP <br/>
–WS-X6724-SFP—24-port Gigabit Ethernet SFP <br/>
–WS-X6816-GBIC—16-port Gigabit Ethernet GBIC <br/>
–WS-X6748-GE-TX—48-port 10/100/1000 RJ-45<br/>
'''The above cards are supported in the cisco7603-S chassis'''

==Supervisor engines==
[[image:Cisco7603 front.jpg|framed|Cisco7603 front]]
[[image:Cisco7603 rear.jpg|framed|Cisco7603 rear]]
[[image:Cisco7603-S front.jpg|framed|Cisco7603-S front]]
[[image:Cisco7603-S rear.jpg|framed|Cisco7603-S rear]]
Both, the Cisco7603 and the Cisco7603-S router have three horizontal slots being numbered from top to bottom and measure 4 rack units (4 RU).<br/>
While slot 1 is reserved for the supervisor engine, slot 2 can contain an optional redundant supervisor engine.<br/>
''!!! Note: When installing a redundant supervisor engine, both supervisor engines must be identical.''<br/>
''!!! Note: The GBIC uplink ports are fully functional on the redundant supervisor engine in stand by.''<br/>
If a redundant supervisor engine is not required, slot two can be equipped with any supported cisco7600 series / catalyst 6500 series module.<br/>

'''Supported supervisor engines in the Cisco7603 router'''<br/>

*Supervisor engine 2<br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-X6K-S2-PFC2]]<br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-X6K-S2-MSFC2]] <br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-X6K-S2U-MSFC2]] <br/>

*Supervisor engine 720<br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-SUP720]] <br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-SUP720-3B]] <br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-SUP720-3BXL]] <br/>

''!!! Note: While being supported in the WS-C6503 and WS-C6503-E chassis, the supervisor engine 32 is not supported in the ciso7603 router''

'''Supported supervisor engines in the Cisco7603-S router'''<br/>

*Supervisor engine 32<br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-SUP32-GE-3B]] <br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-SUP32-10GE-3B]] <br/>

*Supervisor engine 720<br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-SUP720]] <br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-SUP720-3B]] <br/>
** [[Cisco catalyst 6000 / 6500 series supervisor engines | WS-SUP720-3BXL]]<br/>

*Route switch processor 720<br/>
**RSP720-3C-GE<br/>
**RSP720-3CXL-GE<br/>

''!!! Note: the supervisor engine 2 is not longer supported in the Cisco7603-S router.''<br/>

==Power supplies and power entry modules==
Both, the Cisco7603 and the Cisco7603-S router have two power supply slots on the back of the chassis, with the power supply 1 being installed on the bottom and the optional redundant power supply 2 being installed in the upper of the two slots.<br/>

'''Supported spower supplies in the Cisco7603 router'''<br/>
*950 watt AC-input power supply<br/>
**PWR-950-AC<br/>
''!!! Note: the power entry module '''PEM-15A-AC ''' is needed when using a PWR-950-AC. You need one '''PEM-15A-AC ''' per PWR-950-AC.<br/>''
''The power entry modules are installed on the front of the chassis on the very top.''

*950 watt DC-input power supply<br/>
**PWR-950-DC<br/>
''!!! Note: the power entry module '''PEM-DC/3''' is needed when using a PWR-950-DC. You need one '''PEM-DC/3''' per PWR-950-DC.<br/>''
''The power entry modules are installed on the front of the chassis on the very top.''

*1400 watt AC-input power supply<br/>
**PWR-1400-AC<br/>
''!!! Note: the power entry module '''PEM-20A-AC+''' is needed when using a PWR-1400-AC. You need one '''PEM-20A-AC+''' per PWR-1400-AC.<br/>''
''The power entry modules are installed on the front of the chassis on the very top.''

'''Supported spower supplies in the Cisco7603-S router'''<br/>
*1500 watt DC-input power supply<br/>
**PWR-1500-DC<br/>
''!!! Note: the power entry module '''PEM-1500W-DC/03S''' is needed when using a PWR-1500-DC. You need one '''PEM-1500W-DC/03S''' per PWR-1500-DC.<br/>''
''The power entry modules are installed on the front of the chassis on the very top.''<br/>
'''''There is no longer an AC power supply option for the Cisco7603-S router'''''

==Fan trays==

'''Supported fan trays in the Cisco7603 router'''<br/>
*standard fan module<br/>
**FAN-MOD-3<br/>
*high speed fan module<br/>
**FAN-MOD-3HS<br/>
''!!! Note: supervisor engine 720 configurations require the '''FAN-MOD-3HS'''. '''The FAN-MOD-3''' will only work in supervisor engine 2 configurations.''<br/>

'''Supported fan trays in the Cisco7603-S router'''<br/>
*high speed fan module<br/>
**FAN-MOD-3SHS<br/>
''!!! Note: As a result of the sup 32 being the minimum required supervisor engine for the Cisco7603-S, no standard fan tray is supported in any cisco7603-S configuration. Both high speed fans, the FAN-MOD-3SHS and the FAN-MOD-3HS will work in the Cisco7603-S. With the FAN-MOD-3SHS being white, the colour would be the only difference.''<br/>