Difference between revisions of "Password Recovery Procedure for the Cisco AIR-CAP2602I-E-K9"
From NesevoWiki
Jump to navigationJump to searchm |
m (Wrapped commands in <code> elements) |
||
Line 7: | Line 7: | ||
Ethernet speed is 100 Mb - FULL Duplex | Ethernet speed is 100 Mb - FULL Duplex | ||
− | '''Step 3''': Issue the '''flash_init''' command and the '''load_helper''' command: | + | '''Step 3''': Issue the '''<code>flash_init</code>''' command and the '''<code>load_helper</code>''' command: |
If the Flash has already initialized, you see this: | If the Flash has already initialized, you see this: | ||
Line 30: | Line 30: | ||
Parameter Block Filesystem (pb:) installed, fsid: 4 | Parameter Block Filesystem (pb:) installed, fsid: 4 | ||
− | Issue the '''load_helper''' command in order to load any boot helper images. Here is an example: | + | Issue the '''<code>load_helper</code>''' command in order to load any boot helper images. Here is an example: |
ap: '''load_helper''' | ap: '''load_helper''' | ||
Line 36: | Line 36: | ||
− | '''Step 4''': Issue the '''reset''' command followed by an '''y''' to approve the reset. | + | '''Step 4''': Issue the '''<code>reset</code>''' command followed by an '''<code>y</code>''' to approve the reset. |
ap: '''reset''' | ap: '''reset''' | ||
Are you sure you want to reset the system (y/n)?'''y''' | Are you sure you want to reset the system (y/n)?'''y''' | ||
Line 49: | Line 49: | ||
− | '''Step 5''': Let the machine normally boot up this time. The default username and password after a reset should be '''Cisco'''[https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/9215-pwrec-2.html#resios]: | + | '''Step 5''': Let the machine normally boot up this time. The default username and password after a reset should be '''<code>Cisco</code>'''[https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/9215-pwrec-2.html#resios]: |
User Access Verification | User Access Verification |
Revision as of 11:38, 10 October 2019
Step 1: Hold the mode Button down for approximately 20 seconds while powering up the access point. The Indicator LED should end to be blinking in red
Step 2: Issue the ether_init
command:
ap: ether_init Initializing ethernet port 0... Ethernet speed is 100 Mb - FULL Duplex
Step 3: Issue the flash_init
command and the load_helper
command:
If the Flash has already initialized, you see this:
ap: flash_init Initializing Flash... ...The flash is already initialized. ap:
If the Flash has not initialized, you see this:
ap: flash_init Initializing Flash... flashfs[0]: 21 files, 2 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 7741440 flashfs[0]: Bytes used: 4499456 flashfs[0]: Bytes available: 3241984 flashfs[0]: flashfs fsck took 7 seconds. ...done initializing flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4
Issue the load_helper
command in order to load any boot helper images. Here is an example:
ap: load_helper ap:
Step 4: Issue the reset
command followed by an y
to approve the reset.
ap: reset Are you sure you want to reset the system (y/n)?y System resetting... IOS Bootloader - Starting system. flash is writable FLASH CHIP: Macronix Mirrorbit (00C2) Xmodem file system is available. ...
Step 5: Let the machine normally boot up this time. The default username and password after a reset should be Cisco
[1]:
User Access Verification Username: Cisco Password: Cisco APxxxx.xxxx.xxxx>